
In-screed floor heating
For living areas and whole floors where the slab is already down. ELEKTRA DM20 cable is laid over the floor and covered by a sand-cement screed before the floor finish.
ELEKTRA DM20 heating cable.
The same twin-conductor DM20 cable used under tiles, laid across larger areas and covered by the screed. We select each cable length from your layout, zone by zone, so nothing is cut on site.

Everything else, when you need it.
Sizes, installation and common questions. Open any section.
All 21 DM20 sizesPart numbers, lengths, outputs
| Part no. | Length (m) | Output (W) | Approx. area (m²) | Current (A) |
|---|---|---|---|---|
| SIEDM125 | 6.5 | 125 | 0.7 | 0.5 |
| SIEDM195 | 10 | 195 | 1 | 0.8 |
| SIEDM215 | 11 | 215 | 1.1 | 0.9 |
| SIEDM280 | 14 | 280 | 1.4 | 1.2 |
| SIEDM325 | 16.5 | 325 | 1.7 | 1.4 |
| SIEDM365 | 18.5 | 365 | 1.9 | 1.5 |
| SIEDM420 | 21 | 420 | 2.1 | 1.8 |
| SIEDM470 | 23.5 | 470 | 2.4 | 2.0 |
| SIEDM600 | 29.5 | 600 | 3 | 2.5 |
| SIEDM660 | 33.5 | 660 | 3.4 | 2.8 |
| SIEDM820 | 40.5 | 820 | 4 | 3.4 |
| SIEDM1030 | 51 | 1,030 | 5.1 | 4.3 |
| SIEDM1150 | 58 | 1,150 | 5.8 | 4.8 |
| SIEDM1280 | 64 | 1,280 | 6.4 | 5.3 |
| SIEDM1440 | 73 | 1,440 | 7.3 | 6.0 |
| SIEDM1640 | 81 | 1,640 | 8.1 | 6.8 |
| SIEDM1940 | 98 | 1,940 | 9.8 | 8.1 |
| SIEDM2410 | 122 | 2,410 | 12.2 | 10.0 |
| SIEDM3000 | 150 | 3,000 | 15 | 12.5 |
| SIEDM3520 | 177 | 3,520 | 17.7 | 14.7 |
| SIEDM4050 | 205 | 4,050 | 20.5 | 16.9 |
Stocked range. Approximate area is at 100 mm cable spacing; your layout sets the exact cable. Current is calculated at 240 V.
Know the part numbers? Order any of these and send the list for trade pricing.
Order by part numberFixing and testing partsTape, fixing strip, break alarm
| Part no. | Description |
|---|---|
| SIETXXP5013 | Heating cable break alarm |
| SIETXXP5012 | Cloth fixing tape, 25 m x 48 mm |
| SIETXXP5014 | Fixing strip, 25 m roll |
Know the part numbers? Order any of these and send the list for trade pricing.
Order by part numberWhere it is used
- Renovations over an existing slab. Living rooms, kitchens and hallways being re-floored.
- Upper floors and extensions. Where a screed is going down over the structure.
- Whole floors in zones. Each room on its own thermostat.
For a single bathroom or small tiled room, see under-tile heating. For a slab that has not been poured yet, see in-slab heating.
How it goes in
- Layout. Send the plan. We draw the cable layout, clear of cabinetry and fixed joinery, with the zone loads for your electrician. Within 24 hours, at no cost.
- Rough-in. The electrician runs a draw wire to each thermostat position.
- Laying. The cable is laid at 100 mm spacing to the layout and megger tested.
- Screed. The screed goes down over the tested cable, with a break alarm connected. The cable is tested again after covering.
- Fit-off. After the floor finish, the electrician fits the thermostat off like a normal power point.
Thermostats and control
Every zone has its own thermostat with a floor sensor in a capped protective conduit. Programmable and Wi-Fi models are available.
See every model on the thermostats and controls page.
Floor coverings
Tile and stone are the most common finishes over a heated screed. For engineered timber, vinyl and floating floors, ask before ordering. The answer depends on the flooring manufacturer’s rating.
Repairs
If a floor stops working, we carry a thermal imaging camera and fault-finding equipment to locate the exact spot. The repair is usually a small section of floor. We repair the ELEKTRA systems we supply. See floor heating repairs.
Common questions
Is in-screed the same cable as under-tile?
Yes. Both use ELEKTRA DM20. Under-tile jobs are usually single rooms in self-leveller; in-screed jobs cover larger areas under a sand-cement screed.
Can the cable be cut to fit?
No. We select the correct length for each zone from the layout.
Who connects it?
A licensed electrician fits the thermostat off and makes the final connection.
What is the warranty?
Twenty years on the DM20 cable. Thermostats carry a one to three year warranty, depending on the model.
Send your plans. Free layout within 24 hours.
Email info@papheatingsolutions.com.au or call (02) 6242 9310. We provide the layout design and load requirements at no cost.